Puss In Boots: Difference between revisions

From RPCS3 Wiki
(Typo fix)
m (Text replacement - "==Configuration==↵<!-- Enter mandatory non-default settings to be used. Recommendatory or default settings can be entered only on exceptional basis. -->{{config↵<!-- CPU configuration -->↵|ppu decoder = <!-- Interpreter (precise), Interpreter (fast), Recompiler (LLVM) -->↵|ppu decoder notes = ↵|spu decoder = <!-- Interpreter (precise), Interpreter (fast), Recompiler (ASMJI...)
Line 16: Line 16:
<!-- Enter mandatory non-default settings to be used. Recommendatory or default settings can be entered only on exceptional basis. -->{{config
<!-- Enter mandatory non-default settings to be used. Recommendatory or default settings can be entered only on exceptional basis. -->{{config
<!-- CPU configuration -->
<!-- CPU configuration -->
|ppu decoder                          = <!-- Interpreter (precise), Interpreter (fast), Recompiler (LLVM) -->
|ppu decoder                          = <!-- Interpreter (static), Interpreter (dynamic), Recompiler (LLVM) -->
|ppu decoder notes                    =  
|ppu decoder notes                    =  
|spu decoder                          = <!-- Interpreter (precise), Interpreter (fast), Recompiler (ASMJIT), Recompiler (LLVM) -->
|spu decoder                          = <!-- Interpreter (static), Interpreter (dynamic), Recompiler (ASMJIT), Recompiler (LLVM) -->
|spu decoder notes                    =  
|spu decoder notes                    =  
|preferred spu threads                = <!-- Auto, Single digit between 1 to 6 (e.g. 3), Range between 1 to 6 (e.g. 1 - 3) -->
|preferred spu threads                = <!-- Auto, Single digit between 1 to 6 (e.g. 3), Range between 1 to 6 (e.g. 1 - 3) -->
Line 24: Line 24:
|thread scheduler                      = <!-- Operating System, RPCS3 Scheduler, RPCS3 Alternative Scheduler -->
|thread scheduler                      = <!-- Operating System, RPCS3 Scheduler, RPCS3 Alternative Scheduler -->
|thread scheduler notes                =  
|thread scheduler notes                =  
|lower spu thread priority            = <!-- On, Off -->
|lower spu thread priority notes      =
|enable spu loop detection            = <!-- On, Off -->
|enable spu loop detection            = <!-- On, Off -->
|enable spu loop detection notes      =  
|enable spu loop detection notes      =  
|spu cache                            = <!-- On, Off -->
|spu cache notes                      =
|spu xfloat accuracy                  = <!-- Accurate, Approximate, Relaxed -->
|spu xfloat accuracy                  = <!-- Accurate, Approximate, Relaxed -->
|spu xfloat accuracy notes            =  
|spu xfloat accuracy notes            =  
Line 41: Line 37:
|aspect ratio                          = <!-- 4:3, 16:9 -->
|aspect ratio                          = <!-- 4:3, 16:9 -->
|aspect ratio notes                    =  
|aspect ratio notes                    =  
|framelimit                            = <!-- Off, 59.94, 50, 60, 30, Auto -->
|framelimit                            = <!-- Off, 50, 60, 30, Auto, PS3 Native, Infinite -->
|framelimit notes                      =  
|framelimit notes                      =  
|anisotropic filter                    = <!-- Auto, 2x, 4x, 8x, 16x -->
|anisotropic filter                    = <!-- Auto, 2x, 4x, 8x, 16x -->
Line 49: Line 45:
|zcull accuracy                        = <!-- Precise, Approximate, Relaxed -->
|zcull accuracy                        = <!-- Precise, Approximate, Relaxed -->
|zcull accuracy notes                  =  
|zcull accuracy notes                  =  
|shader quality                        = <!-- High, Low, Auto -->
|shader quality notes                  =
|3d rendering mode                    = <!-- Disabled, Anaglyph, Side-by-side, Over-under -->
|3d rendering mode notes              =
|default resolution                    = <!-- 1920x1080, 1280x720, 720x480, 720x576, 1600x1080, 1440x1080, 1280x1080, 960x1080 -->
|default resolution                    = <!-- 1920x1080, 1280x720, 720x480, 720x576, 1600x1080, 1440x1080, 1280x1080, 960x1080 -->
|default resolution notes              =  
|default resolution notes              =  
Line 65: Line 65:
|stretch to display area              = <!-- On, Off -->
|stretch to display area              = <!-- On, Off -->
|stretch to display area notes        =  
|stretch to display area notes        =  
|enable 3d                            = <!-- On, Off -->
|enable 3d notes                      =
|disable vertex cache                  = <!-- On, Off -->
|disable vertex cache                  = <!-- On, Off -->
|disable vertex cache notes            =  
|disable vertex cache notes            =  
Line 134: Line 132:
|disable on-disk shader cache          = <!-- On, Off -->
|disable on-disk shader cache          = <!-- On, Off -->
|disable on-disk shader cache notes    =  
|disable on-disk shader cache notes    =  
|disable native float16 support        = <!-- On, Off -->
|disable native float16 support notes  =
|rsx fifo accuracy                    = <!-- Fast, Atomic, Ordered & Atomic -->
|rsx fifo accuracy                    = <!-- Fast, Atomic, Ordered & Atomic -->
|rsx fifo accuracy notes              =  
|rsx fifo accuracy notes              =  

Revision as of 07:57, 25 April 2023

Puss In Boots
Developer(s) Blitz Games
Publisher(s) THQ
Release date(s) NA October 25, 2011
EU December 2, 2011
Release type Console exclusive
Genre(s) Action
Mode(s) Single-player, Multiplayer
GameID(s) BLUS30731 (IRD), BLES01308 (IRD)
Quick links Check Compatibility
Open Issues
Search Google
Wikipedia Page


Configuration

No options that deviate from RPCS3's default settings are recommended for this title.

Known Issues

There are no reported issues with this title.

Special Notes