m (Text replacement - "==Configuration== <!-- Enter mandatory non-default settings to be used. Recommendatory or default settings can be entered only on exceptional basis. -->{{config <!-- CPU configuration --> |ppu decoder = <!-- Interpreter (precise), Interpreter (fast), Recompiler (LLVM) --> |ppu decoder notes = |spu decoder = <!-- Interpreter (precise), Interpreter (fast), Recompiler (ASMJIT), Recompiler (LLVM) --> |spu...) |
Marcus Rivet (talk | contribs) |
||
| Line 168: | Line 168: | ||
==Special Notes== | ==Special Notes== | ||
<!-- Mention any additional notes if necessary. If no special notes are required, remove this section --> | <!-- Mention any additional notes if necessary. If no special notes are required, remove this section --> | ||
Game will crash if sustained below or above 30 frames per second for too long, therefore it is important that you lock the framerate to 30 fps and have a CPU which is powerful enough to sustain that framerate. | |||
In order to use the Buzz controllers with RPCS3 read and follow the steps below: | |||
After connecting the USB for your wireless or wired Buzz controllers, you need to make sure it uses WinUSB drivers, or else your game will crash instantly. For this you can use a software called Zadig. Step by step guide below: | |||
1: Plug in the USB for your wireless or wired Buzz controllers into a USB-port on your PC. | |||
2: Install Zadig on your Computer (https://github.com/pbatard/libwdi/releases/download/v1.4.1/zadig-2.7.exe). | |||
3: Open Zadig, select 'Options', then select 'List all devices'. Then in the scroll window, you will now see a lot of devices, find which device is the USB to your Buzz controllers (most likely it is a device called 'Wbuzz'). once you've find the correct device, select it, then you need to click either of the up/down arrows next to the right window until it shows 'WinUSB' and click 'Replace driver'. Then it may give you a warning but just hit 'Yes' or 'Ok' on it to proceed with the install. Wait while it installs and applies the driver. Once finished you should be able to launch any of the Buzz games and play them with your Buzz controllers. NOTE: If you place the Buzz USB into another USB-port on your PC, you will have to re-do this process. | |||
CONNECTING WIRELESS BUZZ CONTROLLERS: | |||
To connect your wireless buzz controllers, press and hold the power button on your wireless buzz controllers until the blue light on the controller is on (Must be continuously lit, not blink). Do this to all 4 of your Wireless Buzz controllers, once all 4 of your wireless Buzz controllers blue light is lit up, press and hold the button on the Wireless Buzz USB receiver until the huge red buttons on your Wireless Buzz controllers start blinking and you are done. | |||
Revision as of 14:37, 6 June 2022
| Buzz! Brain of... | |
|---|---|
| GameID(s) | |
| Quick links | Check Compatibility Open Issues Search Google Wikipedia Page |
Configuration
No options that deviate from RPCS3's default settings are recommended for this title.
Known Issues
There are no reported issues with this title.
Special Notes
Game will crash if sustained below or above 30 frames per second for too long, therefore it is important that you lock the framerate to 30 fps and have a CPU which is powerful enough to sustain that framerate.
In order to use the Buzz controllers with RPCS3 read and follow the steps below:
After connecting the USB for your wireless or wired Buzz controllers, you need to make sure it uses WinUSB drivers, or else your game will crash instantly. For this you can use a software called Zadig. Step by step guide below:
1: Plug in the USB for your wireless or wired Buzz controllers into a USB-port on your PC.
2: Install Zadig on your Computer (https://github.com/pbatard/libwdi/releases/download/v1.4.1/zadig-2.7.exe).
3: Open Zadig, select 'Options', then select 'List all devices'. Then in the scroll window, you will now see a lot of devices, find which device is the USB to your Buzz controllers (most likely it is a device called 'Wbuzz'). once you've find the correct device, select it, then you need to click either of the up/down arrows next to the right window until it shows 'WinUSB' and click 'Replace driver'. Then it may give you a warning but just hit 'Yes' or 'Ok' on it to proceed with the install. Wait while it installs and applies the driver. Once finished you should be able to launch any of the Buzz games and play them with your Buzz controllers. NOTE: If you place the Buzz USB into another USB-port on your PC, you will have to re-do this process.
CONNECTING WIRELESS BUZZ CONTROLLERS: To connect your wireless buzz controllers, press and hold the power button on your wireless buzz controllers until the blue light on the controller is on (Must be continuously lit, not blink). Do this to all 4 of your Wireless Buzz controllers, once all 4 of your wireless Buzz controllers blue light is lit up, press and hold the button on the Wireless Buzz USB receiver until the huge red buttons on your Wireless Buzz controllers start blinking and you are done.